Sunday, 27 January 2013

Wheel Arch Storage

So it’s been a while since I last worked on  my Defender, but no that Xmas is over I can start to invest in new parts. Next job on my list is to spray all the parts currently off the Defender, but before I can do this I needed to modify the wheel arch and install storage space.

The new storage area will be in the wheel arch on the passenger side, here:



So I removed the rubber mud flap.


Then cut out the front section and started folding the returns.



I then test fitted the new side panel.




 Then on to the bottom section.



Which was then test fitted.



It was then time to cut in the lid. I wanted to be able to access the storage from inside the vehicle so decided to cut the lid into the top of the wheel arch. The same as 109s used to have.





Then the panels had sealant run along the edges and they were riveted into place.




Then more sealant was applied to the outside.




Finished!



Sunday, 2 September 2012

Fitting the new axle and spraying the rear cross member.

I recently started to fit the new rear axle. First task was to install the dislocation cones in to the turrets.


Once both of these had been fitted I dragged the axle into place and attached the springs to the spring plates. I have decided to install all my new suspension components while changing the axle, as it's already off installing now will save some time. However I will not be using my new springs as they are for heavy vehicles and unladen could rip the shocks apart. So for the time being spaces have been used with the stock springs to give the lift, and I will swap over the springs when the Defender has reached the correct weight.



 Then lifted the axle into place and held it with some straps while I went around connecting every thing up. Here you can see the new radius arms with new bushes installed.


New shock installed, and radius arm connected.


The paint also arrived for the rear cross member, so I masked it up.


And then started spraying - first layer of undercoat.


While that was drying I put the Defender back on all four wheels.


Here is the cross member after 2 under coats and 3 top coats. there will be 1 maybe 2 more coats and its done. Picture is a big crap, but it looks really good! Just hope I don't need to modify it in the future.


I also had to take the self levelling unit off again,so the brackets got sprayed in chassis paint and the arms got some Dinitrol. Then the bushes were fitted.


Now I'm waiting for some more bits to be delivered and for some more money before I can continue........


Sunday, 19 August 2012

Building and Fitting the axle

In between the small amount of time I have hand off work over the last few weeks I have cracked on with a few jobs.

First up the newly painted hub had the treads cleaned out, and the over spray cleaned off area where paint isn't needed.


Then I installed the bearing races and removed a 2nd wheel stud, as I found another which was damaged.


Then fitted the a new wheel stud.


After this I installed grease, bearings, more grease, seals and yet more grease. Once complete on went the new discs.



The hubs and disc went on to the axle, then the washers and first axle nut.


At this point it was time to measure the free-play with a DTI, as seen below.


Once the free-play was correctly set, the half-shafts were installed and bolted up.


Then I quickly stuck on the wheels and dropped the axle off the bench.


I then jacked up the rear of the Defender, off the chassis so the wheels were off the floor.


The prop shaft and brake line was then disconnected.


I then removed the radius arms and shock, which allowed the axle to drop on to a axle stand.


The same was repeated on the other side, springs removed, and the axle was dragged out.


One old axle, looking for a new home.....


At this point I decided to dummy fit some of the nice D44 kit I had brought, here it is.

Saturday, 4 August 2012

Plodding on.


Over the last few weeks I have been continuing with the refurb of the axle, self-levelling unit, and a few smaller jobs along the way.

First up I finished off painting the self-levelling unit which I had previously removed.


The next job was to wire brush the rear axle ready for paint.


After degreasing, the axle received a spray of undercoat.


During paint coats I set about repairing a spot of rust in the outrigger, first I wire brushed the wax off.



Then cut back the rust ready to weld up.



All welded up.



Then added a layer of wax to protect it from the elements.



Another job I had to do was to paint the return fuel filter cover as every time I unscrewed it petrol would flow over it, taking off the wax. So it needed to be painted. First up I removed the sleeve from its postion.



Then cleaned it up and gave it and its bolt a few coats of chassis paint.




I had quite a few items to spray….


 Here is the axle with its final coat.



I also fitted and X-Eng plug, which plugs the oil drain and also has a magnet to capture any loose metal inside the diff, which I thought was a good idea.



Another job I took care of in between painting (lots of waiting around) was to strip back my newly acquired steel wheels.